Exel Composites (Nanjing) is a source-reviewed supplier profile for carbon fiber tube, pultruded, and pultruded fiberglass, with every search topic tied to company-published product or process evidence and separated from buyer-side verification requirements.
Exel Composites (Nanjing) Co., Ltd. is Exel Composites' manufacturing entity in China. Exel's current China page states that its Chinese footprint includes pultrusion and product-design R&D and manufactures composite profiles for multiple industries; the current contact page continues to publish a Nanjing office email and China telephone number. Company disclosures show that two Nanjing-area manufacturing sites were consolidated into one in 2022 and the closed property was sold. Later 2024 and 2025 disclosures continue to identify a Nanjing factory for pultruded wind-power components, so this profile uses the current consolidated Nanjing manufacturing scope and does not reproduce the closed site's address. China Composites Expo lists the same Chinese and English entity. Identity, products and capabilities are company- or organizer-published and have not been independently site-audited by GetFRP.
The reviewed product and process scope makes this supplier relevant to buyer searches for carbon fiber tube, pultruded, pultruded fiberglass, and custom carbon fiber tubing. These phrases describe products or processes supported by the cited public scope; they do not expand the supplier's catalog or replace technical qualification.
Is this your business?
Register or sign in to claim your company, update this public profile and respond to buyer inquiries.
This procurement profile is built for engineering and procurement teams comparing a finished FRP or composite component against a controlled drawing, service condition and inspection plan. It organizes Exel Composites (Nanjing) Co., Ltd.'s published products, processes, certificate references and official sources around the primary topic “Exel Composites (Nanjing) Pultruded FRP Profiles.” The objective is to help a buyer decide whether to open a controlled RFQ, not to turn a broad company catalog into an unsupported approval.
Exel Composites (Nanjing) Co., Ltd. currently lists 5 product or service groups and 6 manufacturing or support capabilities in this reviewed record. The public scope indicates what to investigate, while the buyer remains responsible for drawings, design calculations, standards, current certificates, sample approval and order-specific commercial confirmation. Claims below are attributed to the attached source set unless GetFRP explicitly labels them as qualification guidance.
Exel's group website describes pultrusion, pull-winding and continuous lamination as its continuous manufacturing technologies, but the current China page explicitly assigns only pultrusion and product-design R&D to the Chinese factory. This profile therefore does not automatically mark pull-winding or continuous lamination as Nanjing-site capability. The official process guide explains how pultrusion draws continuous reinforcement through resin impregnation, preforming, a heated cure die, pulling and cut-to-length operations to produce constant-section profiles, with fiber, orientation and resin adjusted for strength, stiffness, durability, environment and electrical requirements. Group products and applications include glass- and carbon-fiber tubes and profiles, telecom and antenna components, window and building profiles, transportation and electrical-insulation components, industrial poles, wind-blade carbon planks and other wind components. An RFQ should first confirm that Nanjing is the actual manufacturing site for the quoted product, then define section drawing, length, straightness, twist, dimensional tolerance, fiber type and volume, mat/fabric/axial-roving architecture, resin system, color and finish, fire/smoke/toxicity, electrical, weathering or chemical requirements, secondary machining, assembly and packing. Mechanical or environmental claims must be tied to the exact lay-up, resin, wall, fiber direction, test method and conditioning. Custom programs should separate design, tooling, first-article approval and repeat production and define tooling ownership, repair, engineering change, batch traceability, first-article records, inspection plan and continuity measures. Exel provides December 2025 group ISO 9001, ISO 14001 and ISO 45001 document links, but buyers must confirm that certificate schedules cover the current Chinese legal entity, Nanjing production address and quoted scope. None is recorded as independently verified until that scope is checked. Older published Nanjing addresses may describe the site closed during the 2022 consolidation; confirm audit, payment and logistics details through the current office.nanjing@exelcomposites.com address and China telephone.
No company-level certification is listed on this profile.
Evaluate Exel Composites (Nanjing) Co., Ltd. as a potential composite product manufacturer for carbon fiber tube, verify the public evidence and prepare a comparable RFQ.
Exel Composites (Nanjing) Co., Ltd. includes this product in its published supply scope. Treat that listing as a starting point: request the current datasheet or drawing, material and construction, available grades or dimensions, guaranteed properties, production site, quotation revision and evidence that represents the exact item offered.
For Custom pultruded CFRP (carbon-fiber) profiles and tubes, buyers should convert the catalog description into an acceptance specification. Confirm standard and custom options, raw-material system, critical tolerances, surface or finish, test basis, sample route, MOQ, lead time and packing. Any alternative proposed by Exel Composites (Nanjing) Co., Ltd. should be identified explicitly rather than treated as automatically equivalent.
This product broadens the supplier's public portfolio, but GetFRP does not infer approval from a product name alone. Ask Exel Composites (Nanjing) Co., Ltd. for the grade or model designation, manufacturing route, current technical file, production and test location, batch traceability and the limits that apply to published performance values.
Exel Composites (Nanjing) Co., Ltd. publishes Continuous pultrusion as part of its capability scope. Buyers should ask which site and equipment perform the work, the practical size or material limits, the normal control records and whether the proposed order uses the same route. Subcontracted stages should be visible in the quality plan.
The relevance of Glass- and carbon-fiber structural design depends on the requested product and acceptance criteria. During qualification, request a process flow, critical control points, inspection or test method, operator or equipment qualification where applicable, nonconformance handling and a recent example that represents the offered production route.
For sourcing purposes, Material, resin and fiber-orientation selection is a capability signal rather than independent verification. Confirm capacity, tooling or fixture availability, setup and changeover assumptions, lot definition, sample approval and traceability. The quotation should identify any limitation that could affect geometry, performance, appearance or delivery.
Buyers evaluating Product R&D, tooling and process development should connect the process claim to evidence: an equipment list, controlled procedure, representative report, production photograph or witnessed sample may each answer a different risk. Exel Composites (Nanjing) Co., Ltd. should also explain how the result is checked before release and recorded for the shipment.
These are sourcing contexts suggested by the published product scope, not confirmed project references. Validate the exact application, design basis and evidence in the RFQ.
Exel Composites (Nanjing) Co., Ltd.'s reinforcement range can be screened for laminating, pultrusion, winding, molding or conversion programs. Buyers should confirm grade, sizing, architecture, width, tex or areal weight, package, splice and moisture limits, then run a representative processing trial before approving the material for repeat production.
Exel Composites (Nanjing) Co., Ltd.'s chemistry portfolio can be evaluated for the named composite process only after the processing window and cured-property basis are aligned. Request current data sheets, grade and site identity, viscosity or mix control, cure and exotherm, storage, batch certificate fields and test evidence based on the intended reinforcement and construction.
Exel Composites (Nanjing) Co., Ltd.'s listed machinery can enter a line comparison when the buyer supplies a written product and process requirement. The proposal should define the complete line boundary, controls, utilities, safety, throughput, acceptance test, installation, training, spares, documentation and the responsibility for proving product quality with representative material.
Exel Composites (Nanjing) Co., Ltd.'s source record currently includes Official Exel China Manufacturing Page, Official Exel Manufacturing-Process Guide, Exel Data Sheets and Certificates, Official Exel China Contact. These links let a buyer distinguish company-published information from GetFRP's own qualification guidance and return to the original context when a claim changes.
No company-level certification is presently listed in the reviewed profile. That does not prove that no document exists, but it means the RFQ should ask for the quality-system certificate and every product-specific test or approval needed by the buyer rather than assuming a certification from market reputation.
GetFRP last recorded a public-source review date of 2026-08-25. Public websites and catalogs can change after review, so commercial decisions should use newly downloaded files and direct supplier confirmation. GetFRP's public or claimed status describes profile ownership and identity controls; it does not certify every product statement or predict order performance.
Official product catalogs, web directories and technical guides published by the supplier.
Current China-site pultrusion, product-design and R&D scope.
Open catalogGroup guide to pultrusion, pull-winding and continuous lamination.
Open catalogCurrent management-system documents and profile/tube data sheets.
Open catalogCurrent Nanjing email and China telephone.
Open catalogOrganizer-published Chinese and English legal identity.
Open catalogOfficial 2022 consolidation and closed-property clarification.
Open catalog
According to its official website, F1 Composites is FengDu New Material's international export company. It supplies pultruded FRP profiles, gratings, fiberglass window and door systems, and custom pultrusions for overseas projects, with English-language engineering, quality documentation, export coordination and international delivery support.
Jiangsu Aosheng Composite Materials Technology Co., Ltd. is a Suzhou-based carbon-composite company whose current corporate website and 2026 China Composites Expo listing support carbon-fiber woven and hybrid fabrics, prepreg, wind-blade pultruded plate and composite application development. The official site also presents automotive, sports, hydrogen, aviation and overseas footprints under the Aosheng group. GetFRP therefore assigns measured-demand phrases such as carbon fiber fabric, carbon fiber plate, pultruded, resin infusion and vacuum infusion only where a published product or manufacturing route supports them. Fishing rods may be an end use of prepreg, but they are not listed here as an Aosheng finished product. Likewise, automotive parts, sports products and hydrogen cylinders are marked as group-sector inquiries rather than automatically attributed to the Jiangsu parent factory. Buyers must confirm the exact legal entity, production site and specification behind a quotation. Awards, customer relationships, capacity, CNAS, patent and standards-participation statements on the website remain company claims, not GetFRP verification.
Nanjing Hitech Composites Co., Ltd. publishes an integrated HICOMA and Lica offer spanning pultruded carbon- and glass-fiber profiles, high-performance reinforcement fabrics and structural adhesives. Its current official catalog explicitly lists carbon-fiber plate, rod, tube, channel, rebar and prestressed plate systems; fiberglass beams, channels, angles, tubes, plates, rebar and grating; carbon- and glass-fiber fabrics; and bonding products for wind blades, carbon plate and civil structures. The China Composites Expo directory independently supports the Nanjing exhibitor identity and its pultruded-composite and epoxy-adhesive scope. GetFRP therefore assigns only demand phrases supported by those actual products, including carbon-fiber products, plates, rods, tubes and fabrics, pultruded fiberglass profiles and fiberglass grating. An application, system or performance label is not treated as a substitute for the offered grade, section drawing, laminate architecture, adhesive TDS or project engineering.